Uncategorized

Hook up oscilloscope

Note also that the probes are measuring voltages away from the common point so the waveforms will be inverted relative to each other. Most 'scopes have an "invert" function on one or both traces to cope with this situation. By clicking "Post Your Answer", you acknowledge that you have read our updated terms of service , privacy policy and cookie policy , and that your continued use of the website is subject to these policies. Home Questions Tags Users Unanswered.


  1. american girl dating indian guy.
  2. ;
  3. Basic Oscilloscope Operation!
  4. lebanese dating sites;
  5. Basic Oscilloscope Operation | AC Electric Circuits Worksheets!
  6. dating means a relationship!
  7. .

How to connect the oscilloscope to a circuit Ask Question. But the ground clips do need to connect to the same node of the circuit and if there is no ground on the scope side, you need to think about that with some care when choosing where to connect the ground clips. My main scope has a two-prong plug, or it can take a 24V battery supply. Sign up or log in Sign up using Google. Sign up using Facebook. Sign up using Email and Password. Post as a guest Name.

probe - How to connect the oscilloscope to a circuit - Electrical Engineering Stack Exchange

Email Required, but never shown. The amount of voltage represented by the vertical divisions varies from trace to trace and is also indicated at the bottom of the screen. The corners peaks of this wave happen at exactly the same time as the edges in the square wave, so it has the same period as the square wave. You can use the built in measurement functions to confirm these values: On the menu on the right side of the screen, select Period by hitting the unlabeled button right next to the item in the menu.

This is just like ATM machines at banks. Select the More menu item to see other options. Keep hitting the More button until the High and Low menu items appear. You should see measurements on the right side of the screen giving you the period, high voltage and low voltage for the square wave. Now, pull up the same information for channel 2. First you need to remove the measurements and then add the measurements for channel two:.


  1. best vacation to hook up;
  2. hook up drawing software.
  3. dating someone with hiv;
  4. Oscilloscope Basics.
  5. greyhound lovers dating.
  6. .

Often, when looking at signals with an oscilloscope, you're looking at a repeating signal. Triggering allows you to horizontally align repetitions of this signal.

How to (Safely) Measure Full Wave Rectified AC Mains On An Oscilloscope

When the oscilloscope sees a trigger event, it knows to put a trace onto the screen horizontally aligned with the Trigger Alignment Indicator. A trigger event happens when the voltage goes past the Trigger Level.

Your Answer

This allows a repeating wave to be overlaid on top of itself in such a way that it reinforces previous traces and makes the trace brighter. You can best appreciate the trigger by moving the trigger level to a voltage that the trace never reaches. For example, move the trigger level to -2 volts and you should see the trace dance across the screen.

Now, move the trigger level back to 0 volts for channel 1 and the trace should stabilize. Sometimes, you would like to look at a signal that doesn't happen often, so you would like to capture the event when it does happen and then be able to view the waveform on the screen. In this mode, the oscilloscope continuously tries to capture data and display it on the screen.

Instead, we'd like to have just a single sequence of data on the screen. You can use the same measurement techniques as before for measuring properties of the wave, or you can use the cursors. The cursors allow you to get very accurate readings of either time or voltage differences between different parts of a wave, or take measurements on things that aren't built-in such as the length of the burst seen in the last section.

You should see the channel two trace go from -1 volts, to a triangle wave of amplitude about mV centered around 0 and then back down to -1 volts.

Oscilloscope Basics

Say you want to find out the amount of time that the channel 2 voltage is above Your first instinct might be to think that the function generator and the triggering mechanism are malfunctioning. In fact, you're seeing aliasing of the signal. This is just something that you need to watch out for when using a digital oscilloscope. Note that only the currently selected trace will be affected by the controls in this group. Note that all traces are affected simultaneously by these controls.

This is useful for horizontally aligning a repeating signal with itself. It also has the autoset button that will cause the oscilloscope to autmatically choose settings for all the other controls that it thinks will best display the current waveforms.