Uncategorized

Need help dating a remington 81

The 8C could be had in a straight grip or semi-pistol grip buttstock. A grip cap for the semi-pistol grip buttstock was optional. Click on the thumbnails below to view typical stock and forearm checkering patterns. A combination of rarity, individual uniqueness, labor involved, and artistic ability is what commands the high prices of these extraordinary custom rifles. Approximately one quarter of the receiver is covered in scroll work. Engraving can also be found on the base of the magazine with little to none on the sides of the magazine.

There is a modest amount of scroll work at the rear of the barrel jacket. Specifications for the 8D stock and forearm were the same as the 8C but with a higher grade of English walnut. The checkering patterns were also a little more elaborate cut to 22 lines-per-inch. The 8E went beyond the D grade with significantly more scroll work, the addition of a game scene on the left side of the receiver, a silver nameplate inlaid in the underside of the stock, and the finest grade of English walnut with checkering cut to 22 lines-per-inch.

A quick look at the magazine box will often distinguish an E grade from a D grade. For the most part D grade magazines are almost bare, whereas the E grades have a generous amount of scroll work on the sides. The left side of the receiver is also a giveaway, as the D is absent of a game scene. Below is the most unique 8E seen during this study.

Without a doubt many, many hours of labor were involved creating these works of art and each rifle is distinctively different. These rifles included a game scene on each side of the receiver and on top of the receiver an animal motif surrounded by scroll engraving. As was customary of Remington, rifles could be ordered just about any way your wallet could handle.

Stock dimensions could be made to order and a couple rifles have been observed with factory gold inlay.

Bolt-Action

Caliber is REM 25 Remington. The Model 81 was basically a facelifted Model 8. The Model 81A had a stock and forearm of plain American walnut and a plain receiver. Like the Model 8A, the Standard grade Model 81 could be ordered with optional checkering but this was seldom. The majority of checkering seen today is not factory. The Model 81 was manufactured with two different forearms. The specifications were the same as the 8C; a hand checkered stock and forearm of English walnut.

Because these rifles were built to order; Remington did not use any special receivers. On average the 81C and 81B cost The 81C was phased out around the serial number range. Model 81B 89XX has a stock with cheeks and a semi-beavertail forearm. Another Model 81B XX has a stock with cheeks, optional pistol grip cap, and the later flatside forearm.

The rifle below is bordered around the entire grip panel. One 81B, with a repair code from Aug. The lines per inch on the forearm and stock do not match but are of the period pattern. Another Model 81B, manufactured in has an unusual forearm checkering pattern. The Model 81D is almost a direct carry over from the Model 8D.

You can order a factory approved part by calling us at or through our online store at www. There are also many aftermarket companies that offer stocks that fit our firearms. Here are 3 examples of companies that offer synthetic stocks that will fit some of our rifles and shotguns:. Brownell's offers a variety of parts for Remington firearms. You can view the products they offer at:. Our tests are conducted in an enclosed area, with a 24" test barrel in most cases, with the barreled action locked into a vice. As a result, your calculations may vary from what we have on our ballistics chart.

Special attention should be taken that oil is removed from action parts. If a lubricant is desired, use dry graphite or similar non-congealing lubricant such as Rem Dri Lube. Note also that as the temperature rises, condensation can occur. There is a jack screw that allows you to regulate the point of aim on the barrels. The left barrel is considered a fixed barrel and the right is a floating barrel. The fixed barrel is set at 50mm. Designed with unique safety and functional features, the Viper is ideal for hunting, plinking, or target shooting use by youngsters and adults.

The strong, lightweight synthetic stock is textured and checkered for good control with a slim pistol grip and semi-beavertail fore-end that fits shooters of all ages. Its strong synthetic receiver is topped with a grooved scope-mounting rail, and the barrel is equipped with adjustable, centerfire-type iron sights. Furnished with 10 round magazine clip. Remington Model was produced from The Model which was offered from was only offered in certain short action and short action magnum calibers. The Model will accept scope mounts. The scope base is a standard Model Seven scope base. You can use a 1 piece or a 2 piece base.

An article in the Army Times January stated that Remington will make M24 Sniper Rifles available to service members for a limited time. There is no set "break in" procedure for the Model ML. We do recommend swabbing the bore between shots with a cleaning patch saturated with Remington All Natural Wonderlube paste.

This helps to remove fouling and will actually season the bore resulting in easier cleaning and increased accuracy. With this muzzleloader, we have received our best results on average using grains of Pyrodex Select and about a grain sabot. However, as with any muzzleloader, you will have to experiment to find which load will provide you with your best performance. This generally provides a good starting point. While the pellets are compatible, we have found our best performance to come with granular powder.

Also, we would recommend swabbing the barrel in between each shot with a pre-lubed Remington cleaning patch to help minimize fouling and further season the barrel. While the Remington Model muzzleloader, can use up to three gr. The Model was completely redesigned from the Model The barrel, bolt, receiver and action bar have been enhanced.


  • how to determine a speed dating rotation sequence.
  • codependent dating signs.
  • Help Center.
  • The Great Model 8 & 81 ยป The Grades of the Model 8 & 81?
  • dating vintage martin guitars.
  • commune dating.

Internal parts are not interchangeable between these models. Rear stocks are interchangeable but fore-ends are not. We no longer house parts for the Model which has been discontinued since If you need parts or service for this model, please check with a Specialty Parts Dealer.

Due to the many variables involved with valuation, we would encourage you to refer to the many publications that are available on the subject of gun values or have it appraised by a collector. Many of these books are available through public libraries or local bookstores. For your convenience we have provided a listing of the more popular books:. Remington does not accept responsibility for the goods or services provided by these sources. The weather shroud is used on the Model ML produced when hunting in adverse weather conditions.

It helps prevent moisture contamination of the powder charge which could result in a mis-fire. The weather shroud should be removed after each use and thoroughly cleaned. Always remember to clean the bolt assembly inside and out as shown in your owner's manual, after using the weather shroud.

We offer a new metal shroud for use with the Primers. Burris offers bases to fit the Model Following are the part numbers. Contact a local dealer to purchase or order these bases. Warne offers bases for both models. Remington does not offer these bases however contact a local dealer with the following part numbers to purchase or order. The magazine assembly for the Model is interchangeable with the Model as long as it is of the same caliber. You can order this item through your local dealer or by calling our parts department at M-F EST. Remington introduced the Model and Model , along with 5mm Remington rimfire ammunition in We believed that the 5mm cartridge, with a velocity of feet per second, was superior to the.

Mag cartridge with a velocity of feet per second. Unfortunately, we were unable to convince the shooting public. Therefore, we chose to discontinue manufacturing the Model and Model in Manufacturing of the 5mm ammunition was discontinued in For additional assistance you may wish to contact the following companies that specialize in older and obsolete ammunition. Martinsburg, WV Ph: Additionally, Aguilla, a Mexico based ammunition manufacturer is now producing 5mm Remington Magnum ammo.

It will be marketed in the U. The R3 pad creates too soft a bearing surface area for this process to function properly. On the Model XR the laminated thumbhole stock features a vented beavertail fore-end for faster barrel cooling. We no longer house any parts for this model. For your convenience we have included a link below to a list of establishments that may offer parts or services for your older Remington firearm.

Many rimfire bullets are made of lead. Because lead bullets are soft they have a tendency to strip or rub off some of their outer material as they travel down the barrel. Most ammunition manufacturers apply a wax-like coating to the bullet which reduces the amount of lead deposited into the bore of the firearm as each shot is fired. This wax lubricant can also assist the feeding of the bullet from the magazine into the chamber in some semi-auto firearms. You can find many of these cleaning products through your local dealer or through our online store at https: Another means of reducing lead fouling in rimfire guns is achieved by applying a very thin layer of copper or brass plating to the bullet.

Remington Model 8

This plating process is usually applied to high velocity rimfire ammunition because lead fouling in the barrel increases as velocity of the ammunition increases. In the vast majority of cases, this is not actually a problem with the batteries. After production of the Remington Digital Optic Systems began, an issue with the programming in the charging cradle was found that would prevent the cradle from recognizing a deeply-discharged battery could be charged.

This would cause the cradle to not charge the battery and turn on the red indicator light when charging was attempted. The sticker used was in two primary forms, but the presence of ANY sticker indicates the cradle firmware is up-to-date. One version was simply a white sticker with the number 2 hand-written on it. See the attached picture. The other common form was a small rectangular sticker.

The largest capacity magazine assembly offered by Remington for the Model and is four rounds. We do not offer any larger magazine assemblies for parts sales nor are these magazines interchangeable. If you wish to purchase a replacement magazine, you can do so through our online store at https: This is a version of the Model that was discontinued in It featured an engraved receiver, trigger guard and high gloss walnut stock. The letter "S" stands for Sporter.

You should thoroughly clean the bolt and firing pin assembly after each use and especially before long term storage. This cleaning should involve removing the firing pin assembly from the bolt and cleaning each with a recommended powder solvent and lubricating oil. Holding the bolt assembly, unscrew the firing pin assembly and slide it out of the bolt body.

Clean the firing pin assembly as a unit. No further disassembly is required. The use of a non-recommended lubricant could cause serious function problems, possibly leading to accidental firing. The PRA Accelerator bullet is designed with an exposed lead tip, in a configuration that is a bit more blunt than a typical. The geometry of the bullet tip combined with the fact that the recoil level of this round in a rifle is very low; makes this round safe to shoot in rifles with tubular magazines.

This is the Remington Model A3. As this gun was built under government contract, at the end of production all records were returned to the Ordnance Commission. If you look on the barrel, just behind the front sight, you will see the date of manufacture stamped there. There were over a million of these guns produced. One scope ring is more than adequate to secure a scope on a single shot, bolt action. Although the Model and Model shotguns are very similar in design we do not recommend that the barrels be interchanged between models.

The extractors and corresponding extractor cuts in the barrel extensions differ. The locations of the barrel seal grooves in the magazine tubes are in slightly different places. Most of all it is an unsafe practice to exchange parts between models unless it is a documented fact that the different models use the same parts. You can view a list of extra shotgun barrels through the parts section of our website located HERE. All RemChokes can be interchanged between Remington RemChoke shotgun barrels as long as they are the same gauge.

You can find a Remington Dealer through our Retail Locator. Yes, the Model , or turkey shotgun can be used for deer hunting. You would need to change either the barrel or choke tube to one that would correspond with the ammunition you would be using. Listed below you will find our choke tube recommendations for deer hunting: If you wish to order an additional choke or replacement barrel, you can do so through your local dealer, by calling our parts department at , or directly through our online store at http: Please provide us with the above information along with a brief description of the gun and we will furnish to you the information that we have available.

You can send this information to the following:. For a complete list of our compact model shotguns, please check the compact section of our site here. For compact model rifles, please check the following link here. Our left handed product line is ever evolving in an attempt to meet the needs of the left handed shooter.

Currently our left hand shotguns are only available in 12 gauge in Model and Versa Max. Please refer to the maintenance section of your owner's manual for proper care maintenance of your firearm. You will need the serial number of the firearm as well as your repair number. The Model 16 gauge with a fixed choke barrel was offered prior to In , it was brought back into production with a Rem Choke barrel. The Model Wingmaster in 16 gauge was produced from and the Model Express was produced from Currently the 28 gauge is only offered in the Model Sporting.

Choke tubes can be purchased through your local dealer, on our online store or by calling us at Clay targets are not considered biodegradable. Studies have not concluded at this time if the targets will ever degrade on land or in water. The targets may be harmful to animals or humans if ingested. We recommend that people do not shoot targets on land where horses or cattle graze or over bodies of water. If you wish to purchase additional keys or for price and availability, you can order these by calling us at M-F EST or order directly through our online store at http: If you are concerned that your gun is involved in a recall we would suggest that you review the information found in our Safety Center at: Many Remington parts can be ordered through our online Country store, to visit the Remington online parts store Click http: Rebuilding, refinishing, and other work take a little longer than standard repairs.

You can find more details about this on the Repair Services page on our website. There are many items that can affect the cycling of an autoloading shotgun. If you have checked these items and your firearm is still not operating properly, we recommend that you have your firearm evaluated by a Remington Authorized Repair Center or our factory. The narrowing found at the muzzle end of most shotgun barrels is a choke. The choke controls the shot pattern and determines at what distance the shotgun will be most effective.

Just as the nozzle on a hose controls the spray of water, the choke of a shotgun barrel controls the spread of the shot. This shot spread is called the "pattern". From the tightest to the widest spread, chokes are described as "full", "modified" and "improved cylinder". A gun that has no choke is called a cylinder bore". If your firearm is designed for interchangeable chokes, always be sure there is a choke tube installed or you could damage the threads in the end of the barrel. Best for trap shooting, pass shooting waterfowl, turkey hunting and shooting buckshot loads.

Excellent for all-around hunting of waterfowl, long-range flushing upland birds such as late-season pheasant and sharptail grouse as well as other small game. Also used for trap shooting. Ideal for close-in small game shooting, upland bird hunting such as quail, grouse and pheasant as well as hunting waterfowl close over decoys. Rifled slugs also perform very well from this choke. Some parts may be restricted.

See parts list for details. This online tracking tool is available 24 hours a day, 7 days a week. While different chokes are offered in different models, these choke tubes and the constrictions is now available in one concise list. If you have an older model Remington firearm and are unsure of the model, you may be able to identify it by the patent date. The Rem Choke tube system is used on a number of Remington shotguns including the Model , Model , and Model Rem Chokes and other shotgun parts can be ordered through your local dealer, by calling our parts department at M-F 9am-5pm EST, or through our online store at http: The Rem choke system is for some Remington barrels that are threaded at the muzzle for interchangeable screw in Remington choke tubes.

Always make sure that you have a choke tube installed when using a Rem choke barrel. You can damage the threads if you shoot your firearm without a choke tube in the barrel. For a list of Remington Choke tubes, please go to our online store at http: We recommend patterning your shotgun to determine which choke constriction provides the best patterns in your shotgun. Typically, most shotguns will produce better patterns with a more open choke constriction; improved cylinder or modified. The more open choke tubes result in less pellet deformity as the shot charge passes through the choke with the larger buckshot pellets and will typically pattern better than a full choke.

Using a rifled choke tube may deform the slug which could then cause an inaccurate shot. Optimal performance with sabot slugs can be obtained from our fully rifled slug barrels. Since these slugs do not have any rifling on them, they will need rifling from the choke tube or fully rifled barrel to insure optimum accuracy. Both the smooth bore barrels and fully rifled barrels as well as a number of choke tubes are available from Remington for most Remington Model , Model , and Model shotguns.

You can order these through your local dealer, by calling our parts department at M-F 9am-5pm EST or through our online store at http: Remington offers a number of extra barrels for the models SP, , , and which can make your firearm more versatile. You can view a number of our extra barrels for these models through our online store at http: Please be sure to follow all warnings and notes regarding extra barrels and proper fit. Some of our shotguns are offered with the designation of "Special Purpose". These shotguns are manufactured for, but not limited to, a particular hunting situation such as waterfowl, turkey, or deer hunting.

They come with additional features which could include slings, camouflage, black matte finish, special choke tubes or special sights. The entire line of Spartan shotgun barrels have chrome lined bores; i. SPR, , , , A pressure-compensating barrel is one that will automatically direct gas pressure through the barrel gas cylinder allowing it to properly react with almost all types of 12 Ga.

The Model Super Magnum is designed to cycle field loads or heavier. These firearms are not designed for target loads. You can download an owner's manual for our current production firearms at www. The thread size of the ivory bead front sight on our blued finish barrels is x A replacement front bead can be ordered direct from the factory by calling or you can order online at http: Please note that some models have a front sight that is pressed in. Since our copper-plated turkey loads use a lead-based shot, they will be safe to use in our Turkey choke tubes or any of our other Lead Only choke tubes.

This includes the Turkey Extended Straight Rifled choke tube as well. Our Trap choke tubes will only be designed for Lead Shot. Our Rifled and Extended Rifled deer choke tubes can be used in vent rib barrels. You can shoot the newer sabot style slugs through these Rem chokes, however your best accuracy with the sabot style slugs will come with a fully rifled barrel. We recommend an improved cylinder choke for shooting rifled slugs and a modified for shooting buckshot. Remington fully rifled barrels should only be used with Sabot Slugs. They are not intended for use with lead or steel shot.

The rifling will deform the shot causing it to be inaccurate. If you are looking for a "multi-purpose" barrel, we would suggest purchasing a smooth bore, Rem-Choke barrel. With this interchangeable choke barrel, you can use a fully rifled choke tube for Sabot Slugs, or an improved cylinder, modified, or full choke for lead or steel shot. Always verify your receiver and barrel type and read the safety instructions on the barrel before use.

With heavy loads there is more than enough gas to properly function the Model Super Magnum. When the gun is operating too fast, this could result in timing related malfunctions, such as: Additionally, this could result in premature wear on the receiver which would be a very expensive repair. You can fit the Model or Special Field with any Model or stock.

You must, of course, use 12 Ga. On the 20 Ga. Keep in mind, some stocks may require a different stock bolt. You can order replacement parts through our parts department by calling M-F 9am-5pm EST. The Model SPRS is cast, however all others are not cast to enable a right or left-hand shooter to use these firearms. Because our firearms are camouflaged by an outside vendor, we would be unable to have your shotgun camouflaged at the factory.

Using the barrel seal activator on firearms other than the Super Mag will prematurely wear out parts by causing excessive bolt speed, without enhancing function or performance. The reason it is used on the Model Super Mag is because of the wide range of ammo that the gun is required to shoot.

In order to allow the Super Mag to shoot a wide variety of loads, we implemented using the barrel seal activator. The Remington factory would not offer camo refinishing, however the following camo vendor may be a source. This is purely for informational reference. The Sportsman series of firearms were designed to bring Remington firearms to the hunter in lower priced versions.

While Sportsman 78 parts will interchange with the Model ADL, we do not recommend exchanging bolts between rifles. Each bolt is individually fitted to each firearm. Should you need to order parts for your firearm, you can contact our Parts and Repair Department at Mon-Fri EST or visit our online store at http: Most of the Remington shotguns are not drilled and tapped for scope mounts.

We do not recommend having this type of alteration done to a receiver that did not come from the factory drilled and tapped. Suggestions for mounting a scope are a saddlemount which mounts over the receiver, or a cantilever barrel. You can view a list of Remington extra barrels through our online store at http: The following after-market dealers may be a source for saddle mounts.

We currently do not offer any firearms directly online. We do sell some parts for firearms direct as well as a variety of accessories but all other products need to be purchased through your local dealer. To view our online store please visit us at http: Remington Turkey Chokes do extend past the end of the barrel. This is normal, and it is safe for all lead Turkey shot. Turkey choke tubes are not designed for use with steel shot.

For options of Remington Choke tubes, please visit our online store at http: Please fill out the repair form from the Repair Services page and include it with the firearms when you send it back to us. If you contact us at or by email HERE. With the model of your firearm and barrel code, we can determine the date of manufacture. The barrel guide stud is only used as an aid when installing the barrel. It has no effect on the function of the firearm, therefore the factory would not need to replace the barrel guide stud if broken. If you still have concerns and wish to have the barrel guide stud reinstalled, please contact us at to obtain a Service Request Number.

It was a 12 gauge autoloading lightweight, low-recoil shotgun and was voted Shotgun of the Year by Shooting Industry magazine. This shotgun was produced from The light contour shotgun barrel is a few ounces lighter than the standard contour barrel due to the thinner contour on the outside diameter of the barrel.

The barrel can still safely shoot factory loaded ammunition with the correct choke installed. Check the markings on the barrel as to what it is chambered for as well as the chokes as to whether it is marked "lead only". To get the figure for the drop at the comb, you measure distance from a straight line extended along the rib of a shotgun rearward toward the butt. Measure the difference to the top of the stock at the comb and the heel. The twist rate of our fully rifled shotgun barrels is 1 twist in 35" in 12 gauge shotgun barrels and 1 in 28" in the 20 ga shotgun barrels.

These barrels are designed to shoot sabots. We do not recommend shooting rifled slugs or buckshot in the fully rifled barrels. This will leave a lead residue in the rifling and will deform the lead projectiles, which will alter the pattern and performance. All of the full choke tubes that are rated for steel or lead are a darker color due to the different type of steel used and the heat treatment. If you wish to purchase additional choke tubes for your shotgun, you can do so through your local Remington dealer, by calling our parts department at M-F EST, or directly through our online store at.

Modern smokeless powders burn in the first 13 to 16 inches of the barrel and maximum velocities are obtained in the first 20 inches. Shot will carry the same distance regardless of the barrel length. Shot pattern will be the same whether the barrel is 21 inches in length or 30 inches in length, if the barrel has the same choke constriction. Our experts state there would be a small variation in velocity when using a inch barrel as compared with a inch barrel; however, the variation would be immeasurable.

The basic advantage of a shorter barrel is that it will swing faster. The longer barrel gives the hunter a longer sight radius to be more precise, particularly when pass shooting waterfowl. Also, the longer barrel can often help balance certain shotguns better. Extra barrels are listed in our online store at. The Model barrels do not interchange with the Model which was discontinued in The dimensions of the receiver are different. Here are some differences, and why they are not interchangeable:.

The gas cylinders are welded in slightly different locations. This is partly because the Model has a longer magazine tube. The Model also has 2 gas orifice holes. The Model is pressure compensated. There is a relief cut made into the gas cylinder to accommodate the spring. The Model gas cylinder will not have the relief cut or the spring or the two additional holes. The extractor relief cut on the Model uses a wider extractor.

Therefore, the extractor cut in the breech end of the barrel will be wider than the Model The barrel extension on the Model has a slightly longer barrel extension. This is the part that connects directly into the receiver. There are actually a couple other slight differences. If you were to use a Model barrel on an Model , basically the barrel will slam back into the receiver every shot. Also, the bolt velocities are increased. Eventually, the front of the receiver will crack, maybe even chip off.

The synthetic stock and fore end will fit the Model If the gun is equipped with the light contour barrel, the fore end fit will be a little loose. You can find a variety of replacement stocks and other parts through our online store at. Remington no longer offers parts or service for the Model This service is offered to replace parts that can be worn over time and to help insure an extended life for the firearm.

You can find instructions for sending your firearm to Laib's Gunsmithing below:. The following parts involved in the update are: Shotgun barrels are classified by "gauge"--a term that refers indirectly to the bore diameter of a shotgun. It is not a direct measurement but is calculated as the number of lead balls of a bore diameter required to make up one pound. This is an old British measurement system. Gauge is determined by taking lead balls the same diameter of the gun's bore, then counting the total number of those lead balls it takes to equal one pound.

You most likely have the Remington Autoloading Shotgun, which was later re-named the Remington Model 11 in This gun was the first successful autoloading shotgun built in the United States. It was designed and patented by John Browning, who reached a licensing and manufacturing agreement with Remington in It was introduced in 12 gauge in , 20 gauge in and 16 gauge in and was discontinued in If you have a noticeable, and often ornate, pattern on the barrel or barrels on an older shotgun, chances are that you have Damascus barrels on the gun.

The pattern on Damascus barrels was a result of the manufacturing process. The barrels were a product of layered steel and iron strips that were heated and forged together, then twisted in a lathe-type device, then heated and twisted around a mandrel while being hammered and welded. Early Model and 20 Ga. The serial number on these shotguns end in an "X" or a "N". The barrel guide ring gas cylinder brazed to the barrel, was a 12 Ga.

These barrels are no longer available from the factory as they were discontinued in The barrels sold now are for the LT 20, which is built on a narrower frame. Its smaller barrel guide ring will not fit over the large frame magazine tube. On our site we have a listing of parts dealers that may offer replacement barrels for your older 20 gauge under "Specialty Parts Dealers". The Special Field shotgun has a shorter magazine tube than the standard This being the case, the barrel guide ring is brazed to the barrel closer to the chamber.

The guide ring on standard barrels won't reach the magazine tube because of its shorter length. On our site we have a listing of specialty parts dealers that may offer replacement Special Field barrels. Specialty Parts Dealers List. It is a combination of velocity and shot charge weight that cycle an autoloading shotgun. The CTI will function 3" magnum shotshells with payload weights up to 2 ounces. No, the single trigger is ejector only. The double trigger that have extractors are extractor only. The 12 gauge models were built on a large frame.

The 20 gauge and 28 gauge were built on a compact frame. However at the time, they were produced in Italy. Remington Arms purchased certain assets of the former Ithaca Gun Company, including their 10 gauge autoloader. We re-engineered the gun and introduced the Model SP to the Remington product line in The remaining Ithaca assets were purchased by Ithaca Aquisition Corporation, and they may be able to offer repair parts for your Mag The difference in the target fore-end and standard for-end for the SPR is that it has hand cut checkering versus pressed checkering and finger grooves are extended to run the length of the fore-end.

Each receiver is fitted to the barrel assembly at the factory and adjusted accordingly. The guns would not function properly if the incorrect barrel was matched up with a different frame. The ejectors for the SPR are controlled by set screws located on the curved portion at the front of the receiver.

The right side set screw controls the ejection of shells from the bottom barrel. The left side set screw controls the ejection of shells from the top barrel. The set screws for the ejectors are preset at the factory for automatic ejection of fired shells when the action is opened. In the automatic setting, the slots in the set screws are oriented in a vertical position running perpendicular to the length of the barrels. While we no longer offer the Spartan series of firearms, when we did offer it, the front bead sight was pressed in on all models except for the Sporting models.

Wipe the outside of your gun with a minimum of Rem Oil to prevent rusting. In , the new gas compensated Model was introduced. While he Model and the Model are similar in design, there are a number of differences which will not allow parts to interchange. The Remington R1 handguns are 80 Series design and feature a firing pin plunger that blocks the firing pin when at rest. The firing pin plunger remains engaged until pressure on the trigger pivots the lower sear lever which in turn actuates the upper plunger lever pressing the firing pin plunger upwards to free the firing pin allowing forward movement when struck by the hammer to discharge the pistol.

The Remington Model R51 is the reinvention of the American subcompact and the definition of shootability. The Remington R1 features a three dot sight system for quick sight accusation. The sight cut is proprietary on this firearm and changes will require the services of a competent gunsmith for proper installation. Additional Magazines may be purchased by visiting our website at www.

Parts may also be ordered direct by phone toll free, Office hours are Monday through Friday 9: Ammunition should be stored in the factory carton or package. The labeling and identification on the original package helps to ensure proper future use. Ammunition should be stored in a locked closet or cabinet in a cool, dry area away from children, and away from firearms.

Help Center | Remington

Obviously, poor storage conditions, such as a humid or corrosive atmosphere, could cause product damage immediately. If ammunition is exposed to fire or if ammunition is older than shelf life, contact your local authorities for assistance with proper disposal. We do not recommend, under any circumstance, interchanging. These cartridges are not interchangeable. You can view ballistics for all of our current loads in the ballistic chart section of our online catalog at www. One of the key differences is the length of the throat or leade on the 5.

Therefore, we recommend against firing the 5. The shelf life of ammunition is about ten years. If ammunition is exposed to extreme temperatures, or if it is older than recommended shelf life, contact local authorities for instruction for proper disposal. You can view ballistics on the loads we offer in our online catalog at www. The 6mm Remington has exactly the same case dimensions as the. They differ only in the fact that the 6mm Remington is loaded with bullets of up to gr.

Ammunition marked 6mm Remington can be fired in. These rifles feature a 1 in inch twist ideal for gr. When there is a concern regarding our ammunition, we request that you please call us at with your Name, Address, type of ammunition, type of failure, and the firearms used.

Once we receive this information, we will forward it to our ammunition plant so that we can send you a prepaid shipping label, and all appropriate packaging materials to send the ammunition back for testing. We will contact you once our evaluation and testing have been completed to determine the best course of action in order to resolve this issue for you. The ballistic co-efficient of a bullet determines its ability to resist air drag, maintain velocity and energy as it flies, to shoot with a flatter trajectory.

The higher the co-efficient the "sleeker" the bullet--making it less susceptible to wind deflection, and velocity or energy loss. A higher BC for the projectile means it will travel further than one with a low BC. Some of the bullets with the highest ballistic coefficients are in our Premier Centerfire ammunition line. The ballistic co-efficient of a bullet must be known in order to calculate accurate trajectories. The ballistic coefficient for the ammunition we offer can be found in the far right column of our Centerfire Rifle Ballistics Table located in the ballistic section of our catalog.

As Remington Arms Company, Inc. This book can be purchased from Amazon. The ISBN number is This book has in-depth ballistic information as well as formulas that will assist you in finding the information you require. This cartridge combines moderate recoil with exceptional accuracy in short action rifles.

We neck down a 7mm Rem. In terms of game-stopping bullet momentum, the. In rimfire, the firing pin blow dents the primer which is located in the rim of the cartridge base. The rim-fire cartridge has no noticeable primer. Instead, the priming compound is placed and spun into the case rim. The Managed-Recoil ammunition was designed to operate at lower pressures than standard velocity ammunition. Because of this it may not cycle semi-automatic firearms. With its large case capacity and our gr. Pointed Soft Point Core-Lokt bullet, it delivers greater velocity, energy and bullet momentum at flatter trajectories out to yards than any other 7mm Magnum.

This cartridge takes full advantage of the 3. The 7mm STW has impressive velocity potential and can deliver good ballistics with a variety of bullets and powders. More information on reloading can be obtained through one of the bullet or powder manufacturers. That's why it says it is okay for any gun in good condition right on the box.

This includes original trapdoor Springfield rifles and both bullet weights that we currently offer. Remington no longer produces Accelerator ammunition for the. Brass is one of the best suited metals for making cartridge cases because of a combination of characteristics: Brass is soft enough to be formed into the many shapes required for different calibers of ammunition, yet hard enough to withstand high pressures when the round is fired in a gun's chamber.

Best of all its low cost allows for shooters, hunters and reloaders to enjoy their favorite shooting sports economically. For Remington Turkey chokes, we recommend using lead shot or copper plated lead shot. This choke patterns too tight for waterfowl and would not be the optimal choke choice.

Over an equal number of rounds, this rubbing is similar to that experienced with steel shot. Both materials create more choke strain than lead shot due to a more solid payload, therefore we do not recommend Hevi-Shot or Wingmaster HD in chokes marked "lead only". Yes, Remington turkey loads contain extra-hard lead shot with Copper-Lokt plating for surface smoothness and added penetration. It can be used in your turkey choke tube or any other Remington choke tube.

We do not recommend the use of steel shot in our 20 gauge FULL chokes or extended chokes. These chokes are designed for lead shot only. A listing of the Remington extra barrels is available through our online store at http: We do not recommend the use of steel shot through any barrel manufactured before or through any barrel having a fixed Full choke. Anything larger would not perform well out of a fixed full choke and could open up your muzzle over time.

If you have barrels manufactured after , with fixed Modified or Improved Cylinder chokes, you may shoot up to size 2 steel shot. The use of steel shot larger than size 2 is only recommended in modern barrels with the Rem Choke system. If you have the Rem Choke system, you may shoot any size steel through the Improved Cylinder and Modified choke tubes. The Full choke tube must state "For Steel or Lead" to be capable of handling steel shot.

If you are using a full choke tube or tighter it is strongly recommended that you use a choke that is stamped for steel and lead. The choke tubes that are stamped for steel and lead are made of heat treated steel that is designed for use with either steel, Hevi-Shot, or Wingmaster HD, or other tungsten based shot materials. Any modern shotgun, in good working condition, designed or recommended for use with steel shot, should be suitable for use with Hevi-Shot or Wingmaster HD. We recommend that a consumer contact the manufacturer for its recommendation. As a result of our extensive testing, we believe that the limited number of rounds used in Turkey Hunting is unlikely to create any more than cosmetic rub marks on chokes not rated for use with steel shot.

Because of the superior ballistic performance of Hevi-Shot and Wingmaster HD pellets, an increase in pattern density versus lead will occur, especially beyond 35 yards. When choke diameters are tighter than. We do not recommend Hevi-Shot or Wingmaster HD in lead only chokes however in laboratory testing, a standard full choke.

Remington's Wingmaster HD extended Turkey choke tube has been optimized with this 0. Many large deer populations exist in areas where civilization and the countryside intersect. For obvious safety reasons, many populated rural areas where deer are hunted require that firearm hunters use shotguns instead of rifles. In some areas, shotgun hunting is even the traditional and preferred way to bag a deer. Habitat usually consists of small wooded tracts with most shots taken at close range around 50 yards with some shots both closer or occasionally longer.

The Remington Buckhammer is a high performance lead slug that's very affordable. Remington Slugger Rifled Slugs: A very popular and economical choice among shotgun deer hunters, Remington Slugger Rifled Slugs deliver outstanding accuracy at short ranges with hard-hitting, reliable expansion.

Each slug is encased in a high-performance plastic sabot that greatly enhances in-flight performance and, thus, accuracy. Delivers concentrated, balanced patterns. Ideal at very short distances ranging from 25 yards and closer. Less recoil means second shot recovery is quicker, allowing the user to get back on target more easily.

These new loads are built with the same precision of our standard 8-pellet 00 Buckshot loads and are buffered for dense patterns, allowing for highly effective performance at up to 40 yards. Any choke tube that is manufactured from high-quality steel, such as stainless, should be acceptable for use with Hevi-Shot or Wingmaster HD. The 16 gauge has a 3 piece hull. The cylinder and improved cylinder chokes can be used for shooting steel or Hevi-Shot.

All others are for lead only. Hevi-Shot doesn't rust like steel shot. However, wet shells can have other significant problems. There is a chance of having a wad stick in the barrel or other problems arising. The Bar and the shell length in millimeters printed on our shells are required by some international government agencies. The Bar actually references the shotgun not the ammunition. The markings are in place so that we can sell our products all over the world.

Navigation menu

The hammer is at rest requiring a full deliberate pull of the trigger to discharge the pistol. The design also incorporates an internal hammer block for additional safety. In centerfire rifles, the firing pin dents the primer which is located in the center of the cartridge base.

It is always best to check with the powder manufacturer when you have a question about a specific recipe. The should not be used in gauges other than the. We do not recommend using pellets and granular powder at the same time in the Model ML because each one has a different burn rate. The plating does not affect the overall length to any degree of significance. The plating also eliminates the oxidation which causes the brass to tarnish.

However, since the plating is a little harder than the brass and the brass surface is etched slightly to hold the nickel, case life is typically a little shorter than with a plain brass case. There are some that are nickel-plated for identification purposes. If the primer has a steel content a magnet will stick to the primer. If it does not stick to the magnet, the primer is made primarily of brass. The substance in the primer is a proprietary mixture.

Dram equivalents were originally developed in the early 20th century to allow sportsmen an easy method of comparing the "new" smokeless powder loads to the then more familiar black powder loads. Overall, the most important thing to remember is that the higher the dram equivalent, the higher the velocity for a given shot weight and, as a result, the more powerful the charge.

There are no real dram equivalents for loads that didn't or couldn't exist in the black powder era. Key examples of these are steel loads and some of the heavy magnum turkey loads. Dram equivalents values have no relationship to the actual powder charge in a shell! These values should never be used in determining smokeless powder charge weights!

An increasing number of black powder shooters prefer the ignition performance of larger-sized musket caps in place of the No. To accommodate their needs and allow the use of tophat or English-style musket caps, Remington is offering a replacement conversion nipple for its Model in-line muzzleloading rifles. Reloading manuals and recipes are available through the following companies:.

Unfortunately, there is no set answer to this question. Primers require not only a certain amount of threshold energy to cause ignition, but the rate of application of that energy is important to the reliable functioning of these devices. Primers are tested by dropping a standardized steel ball from a range of heights.

The percentage that fire from each height is reviewed mathematically to provide a measure of sensitivity. The nickel plating is typically only a few ten thousandths of an inch thick. Prior to the first loading, the inside of the case mouth should be chamfered slightly to remove the plating that builds up due to electrical potential on the edge. This will allow easier seating of the bullets and will not cause scuffing of the bullet's jacket.

Both the Figure 8 and TGT wads now feature a new stitched petal design that helps keeps wads separated for easier reloading and are interchangeable with the older non-stitched versions. The new Pyrodex pellets can also be used--up to gr. However, we have found our best results came with 90 to grains of the granular blackpowder or equivalent. For complete load data, please refer to the Model ML owner's manual. The Model ML barrels are rifled with 1 in 28" twist in both. All testing was done with 2F or FFg black powder. Failing to adhere to these maximum charge weights or substituting any powder type or granulation could result in serious personal injury or death to the shooter or bystanders and damage to the firearm.

The charge weights listed are the nominal range and maximum charge weights for the given projectile. The nominal suggested range of charge weight produces the best combination of accuracy and velocity. It is done by starting at the lower charge weight listed in the nominal range and increasing in 5 grain increments until an optimum load is achieved. An optimum load is one which produces the best accuracy. Do not exceed this charge weight.

To do so may result in serious personal injury or death to the shooter or bystanders and damage to the firearm. For more information regarding reloading, please check your current reloading manual and powder companies. The Remington Primer conversion kit will work on any caliber Remington Model Muzzleloader produced The Model ML conversion kit contains the firing pin assembly, musket cap nipple, the primer nipple, de-priming tool, and the bolt disassembly tool.

The nipple will also be available separately. These kits were all sold as accessories, and with the discontinuation of the Model ML, they may become more difficult to find. We no longer house these parts and would encourage you to check with local gunsmiths in your area to see if you can get them. Remington reloading components can be ordered either through your local Remington dealer or from one of the many companies that specialize in reloading supplies.

Remington does offer apparel such as hats and T-shirts through the lifestyle section of our online store at www. An additional line of clothing and outerwear we offer is our line of Field-inspired apparel for the modern sporting generation. We are under contract with a company to provide our wood products. We would suggest that you contact a high school or college near you with a wood-working program. The students there may be grateful for such an offer. Remington waders are no longer offered. They were a licensed product. For more information concerning Remington waders please contact:.

Remington tents were a licensed product manufactured by American Camper. For more information concerning Remington tents please contact them at:. Our safes are a licensed product offered by Liberty Safe. Please contact Liberty Safes at for assistance with obtaining the combination to your safe. For more information on part orders look HERE. Thank you for thinking of the Remington Arms Company and offering us the opportunity to help assist with your event by providing a donation, or sponsorship.

For organizations in the United States we have a specially designed discount promotional package program which consists of packages that include Remington products, premiums, and literature. At this time, however, we are not able to offer this program to our Canadian friends because of custom regulations and duties, as well as the import permits and export licenses required. Anytime we receive a request for donations or sponsorship we ask that you please forward this request, as well as any supporting documentation to our corporate office by email.

Once received it will be reviewed and you will be notified as soon as possible as to the status of your request. Again we appreciate you thinking of us in this matter and look forward to your submittal. Please send request to the appropriate email address below:. Thank you for your individual support and commitment to your program and its benefits to those who enjoy Remington products in Remington Country. In order to determine the grade, we would need an explicit description of the wood and any engraving on the gun.

Generally, in higher grade guns you will find extensive engraving on the receiver and highly patterned wood. Also, a letter designation of the grade will usually follow the model number of the gun. Forward pictures or details by mail or email to Contact Us. Please be sure to include your name and a contact number in case we need to get in touch with you for more details.

There is a small hole on the bottom left hand corner of the safe.